Recent content by whitescout

https://datebest.net - visit website and win smartphone!

I believe Windtrax sells schneider electric prox switches. https://www.schneider-electric.com/en/about-us/company-profile/history/telemecanique.jsp

Is the wash being triggered? Are you getting an error on the laserwash? If you get an entrance timeout error, then it could be that the ddors are failing to open. If the wash is not being triggered, then it is either an input problem on the laserwash, or and output from the ws2. I know you said...

I highly doubt it is the pump contactor. The coils on the contactor are 24VAC. You are blowing a DC fuse. What I was suggesting in my earlier post, was that your under carriage was not coming on, because you had NO input from the under carriage eyes. The eyes had power, and could see each...

If you are blowing the x30 fuse, then something in the x30-x37 is drawing excess amps, or a short. All of these are inputs, which are DC-. Once this fuse is blown, the controller will not be able to receive any of the inputs from x30 through x37. inputs : width measurement pulse.( picket...

Have you checked your photo eyes in your Tbars yet? I am going to bet that the Stop eyes are creating a short. It could be the photo eye cables, the amplifier or the base, or connections in the j3 box. I am going to bet on the wires in the Tbars are dried, and possibly burnt from the heaters. I...

If you have an exit garage door, the exit door eye may not be "seeing" itself, and think a car is there. This needs to happen to reset machine if garage doors are present.

The Dan Foss valves on your machine are 3/8". I have, and would use one of those. By using one of those, you would not have to stock a completely new item for back up parts. Just power the solenoid to open when the solution pump comes on. Just wire it to the coil for the solution pump. Easy peasy.

You can plumb from the heater right to the starite pump, but if any of the Dan Foss valves leak, you will have issues. If any of the valves for presoak or foam polish leak, you will empty your soap buclets. if the poly or drying agent valves leak, you will empty the bucket, and overflow your...

You can plumb the heater into the starite, but I would add a NC solenoid to the inlet of the pump. The solenoid would be wired to the solution pump contactor, so it opens when the pump turns on. this way, if any of the Dan Foss valves have a leak, you will not drain a soap bucket.

The only thing that can make the arch turn early, is too many pulses from the #30 prox, or an input from the left limit. I would not only check the prox switches, but would check the prox cables as well. ( they are pretty cheap) If it is only happening on a second pass of HP, I would inspect...

The VT and parking eyes get their power from the vtx box where the eyes and sonar run to. The heat is controlled by a thermostat on the bottom of the box. All of these heaters are 24 VAC. If the wires are there, and the thermostat is not working, you could just use the 24 VAC terminals and have...

Bridge heat wires will be number wire number 4 and 5 in the red layer of the festoon cable coming into the J3 box. Tbar heat will be wire numbers 9 and 10 from the yellow layer festoon coming into the J3 box. The Tbar heat is 24vac, no need to worry about polarity. For the bridge heat, 220v...

The axle shafts are the same for a laserwash or a high velocity. The axle shafts for the driver's side bridge, and passenger's side bridge are different. One has two keyways, (gear box, and coupling), and one is coupling only. It sounds to me like you received two of the same parts, and it...

In your post you state T-bar eyes. If I assume that you have a laserwash or high velocity, you can add eyes to the dryers, and use them as exit door eyes, and this will accomplish what you want. If it is a PDQ, simply change the hardware seting, and possibly the bay length setting. If it is a...