|
"DISPENSING THE NEW DOLLAR COIN" BC1200/1400 PROGRAMMING
1.) ENTER PROGRAMMING MODE.
2.) PRESS "FUNCTION" BUTTON UNTIL DISPLAY READS "MC PAYOUT"
3.) PRESS THE "UP" ARROW BUTTON UNTIL DISPLAY READS MC PAYOUT "OFF"
4.) PRESS THE "FUNCTION" BUTTON ONCE, THE DISPLAY READS "HOP VAL"
ALONG WITH TWO OF THE FOLLOWING; T1,T2,T3,5,10,25,50,$1 OR - -.
5.) PRESS THE "VALUE" BUTTON UNTIL THE DISPLAY SHOWS A FLASHING ".25"
ON THE LEFT SIDE.
6.) PRESS THE "HOPPER" BUTTON ONCE, THE DISPLAY WILL NOW SWITCH OVER
TO THE RIGHT SIDE OF THE DISPLAY
7.) PRESS THE "VALUE" BUTTON UNTIL THE DISPLAY SHOWS A FLASHING "$1"
YOU SHOULD NOW HAVE SOMETHING THAT LOOK LIKE THIS (".25 -- $1 ")
8.) PRESS THE "FUNCTION" BUTTON ONCE, THE DISPLAY SHOWS "ACCEPT $1"
(WITH EITHER A "YES" OR A "NO").
9.) PRESS EITHER THE "UP OR DOWN" ARROW BUTTON TO TURN THE $1 ACCEPTANCE
TO YES OR NO.( "YES" TO ACCEPT $1'S., "NO" TO NOT ACCEPT $1'S ).
10.) PRESS THE "VALUE" BUTTON TO GO THROUGH ALL OTHER DENOMINATIONS
YOU WISH TO HAVE THE CHANGER ACCEPT,( OR NOT ACCEPT ) AND PRESS EITHER
THE "UP OR DOWN" ARROW BUTTON TO TURN EACH ONE TO "YES OR NO"
11.) PRESS THE "FUNCTION" BUTTON ONCE, THE DISPLAY WILL NOW SHOW ("$1
PAY XX -- XX")
12.) PRESS THE "UP OR DOWN" ARROW UNTIL THE DISPLAY SHOWS "4" TO THE
LEFT SIDE OF THE DISPLAY, IT WILL NOW LOOK LIKE THIS ("$1 PAY 4 -- XX")
13.) PRESS THE "HOPPER" BUTTON ONCE, PRESS THE "UP OR DOWN" ARROW UNTIL
THE DISPLAY SHOW " 0" ON THE RIGHT SIDE OF DISPLAY, IT WILL NOW LOOK
LIKE THIS ("$1 PAY 4 -- 0").
14.) PRESS THE " VALUE " BUTTON AND REPEAT THE ABOVE STEPS FOLLOW THE
CHART BELOW: "$1 PAY 4 -- 0" "$5 PAY 4 -- 4" "$10 PAY 8 -- 8" FOR QUARTERS
& DOLLARS YOU MUST NOW HAVE YOUR QUARTER HOPPER (BLACK) PART # 65027608
ON LEFT SIDE OF THE DISPENSER AND THE DOLLAR HOPPER (RED) PART # 65027609
TO THE RIGHT OF THE DISPENSER !!!!
15.) PRESS THE "FUNCTION" BUTTON ONCE, THE DISPLAY SHOWS "STACKER MODE
SEP OR ALT" ( SEPabate OR ALTernate ).
16.) PRESS EITHER THE "UP OR DOWN" BUTTON TO SET THE STACKER TO THE
MODE YOU DESIRE. IF SET TO " ALT " THE CHANGER WILL ALTERNATELY STACK
EACH BILL ACCEPTED TO FIRST THE UPPER BILL BOX, AND THE NEXT TO THE
LOWER BILL BOX REGARDLESS OF THE DENOMINATION ACCEPTED. IF SET TO "SEP",
EACH DENOMINATION ACCEPTED CAN BE ASSIGNED TO BE STACKED IN EITHER THE
UPPER OR LOWER BILL BOX.
17.) DO THIS STEP ONLY IF YOU SET THE ABOVE STEP TO "SEP" TO ASSIGN
THE BILLS TO THE UPPER OR LOWER BILL BOX, PUSH THE "VALUE" BUTTON GO
THROUGH EACH DENOMINATION YOU HAVE SET TO "YES" FOR ACCEPTANCE, AND
PUSH EITHER THE "UP OR DOWN" BUTTON TO STACK THESE BILLS IN EITHER THE
"UPPER OR LOWER" BILL BOXES.
18. ) SET UP IS COMPLETE, PUT THE PROGRAMMING SWITCH BACK DOWN TO THE
NORMAL MODE. THE DISPLAY WILL SHOW "STORING NEW DATA" , THEN THE "WALKING
DASH'S" WILL APPEAR.
TOP OF PAGE
|
Print