Search results

My Hamilton RNS C2000 controller gives "Dime input stuck" error intermittently. I don't take dimes!!!! I take $1,5,10 bills only. I can only suspect a bad controller? Ideas?

I'm looking for some aluminum Floor Guide Rails from a Super Wash/ Pro Equipment automatic system. Thanks, Rudy

I've used ZPay's Pay Window for years and years. I only have 3-4 employees, and this "Mom and Pop" software run company has been outstanding. Annual updates were only about $50. Bad news.... The owner is retiring, and "Pay Window" will be no more. Does anyone have a recommendation for a...

I have a MEI bill acceptor that's starting to NOT take $5's in my ShurVend vendor. It takes $1, $10, and $20's ok. Any ideas?

Need Wash Gear swipe up/swipe down system (need 2) for ACW 4.

A long time regular customer leaves a message. Tells me he inserts a brass token (value $10) into the ACW. The machine gives him $.25 in credit (Instead of $10). He tells me that's his last token, so he goes to my vendor, and buys (5) more. Inserts another brass token. The ACW gives him an...

I have the Air Shamee 3 motor in bay dryers. The trigger style nozzles were leaky, and cheaply made. I switched to the Air Logic handles and my usage has gone WAY up. Customers think that I've added air pressure. The new handles are a money maker. The problem? The increased nozzle pressure...

The roof trough that holds the hoses for the bays needs to be replaced. The original trough was made from galvanized sheet metal....the type that's used for ductwork in houses. After 25 years, it's finally rusted past the point of repair. Any suggestions what to use to make a new trough?

I was an early adopter of the original Wobblehead foam brush handle. I've lost track, but after 5+ years, one of the handles is broken. Something feels broken underneath the rubber boot. The head is held on, soley by the rubber boot. It's been VERY quiet (here) about the Wobblehead. Are you...

Does anyone have any experience with Fleck meters? I have a twin tank Fleck 2900 setup with single brine tank and a "Fleck Meter" which counts the gallonage. At a predetermined point, the softeners switch. The used softener regenerates, and the one that was previously "on standby", enters...

My metal security cage for my ShurVend (AMS vending machine) has almost finally rotted to the point of no return after 10 years. I wish that I had opted for Stainless. Any ideas where to get a replacement cage? I've scoured the internet to no avail?

My ACW 4 went out of service with a "Token Input Stuck" error. I reset the the controller, and it went back into service. My first guess....would be to suspect the Slugbuster....yes? BTW....we DO use the Token input to accept brass tokens....and we also use the WashGear Credit card system...

My vending machine needs a replacement for an older Mars (MEI) CF-7512. It's been overhauled, but is finally wearing out. Does anyone have any experience with the CPI Gryphon? I need to find a reliable MDB coin changer....so recommendations are welcome.

I have a 28 year old Cat 623 that has been a workhorse. The crankshaft bearing failed (on the flywheel side) and completely disintegrated. The oil in the crankcase has a grey sludge as a result. I replaced the pump with an Arimitsu 511. It's smaller, and very quiet. (Less than $800) I just...

My Cat 3535 feeds two Dema 458 solenoids. One solenoid opens to provide flow to the undercarriage flush....and the other one feeds high pressure to my spray arch for washing. They are NEVER programed to be open at the same time. Here's my issue.....the undercarriage solenoid isn't completely...

I was rinsing down a bay....when the pump just stopped. I went into the equipment room, and found the circuit breaker to the pump stand tripped. When I reset it....BANG! Smoke came out of the motor starter. (BTW...I hate it when the smoke comes out of electrical things....it's VERY difficult...

Today, I believe I had a mercury relay (DuraKool) intermittently fail ON. Is it possible for a mercury relay to fail ON? I can see how it can fail to close...but stick ON????

Our winter Foam Brush setup uses Methanol for deicing. We have to constantly change the Hydrominder tips depending on the outside air temperature. The colder it is, the more methanol gets pulled into the hydrominder eductor (via a larger tip). We are constantly changing the tips during...

We use BOTH paper TokenNotes as well as Brass Tokens. One of my ACW4's is intermittently giving a $0.25 credit for a $9 brass token (inserted in the Token slot). What could cause the token credit to give only $0.25 instead of the full token value?

Our water is checked for hardness at the start of every day. Typically, we can run 13,000 gallons before the hardness starts edging up. Recently, we've been starting to get hard water at 8,000 gallons....well before the calculated regeneration point. It's been a while since we cleaned the...