Search results

Could you post some pics? I’d like to see how the panels hold up in a self serve after a couple of years.

I’m planning on a late May project, please let me know how yours turns out.

Will do, before and after.

I have put up FRP boards with plastic rivets and everything is visible. The delpro panels are installed over block with their own concrete screws that are completely hidden by the next panel, cut the piece at the end to fit and glue to attach. Then you surround with a tight fitting J channel...

Noob, I did ask about replacing a panel or a piece of a panel. He told me you could cut out a section and glue in a section to replace with regular construction glue. The seem would be visible or You could glue in a full piece. Sounded do able.

So I got a quote from Declan on the vinyl wall panels and the price was almost the same as a quality FRP. The sales guy was pretty knowledgeable and was happy to answer my questions. I’m gonna pull the trigger on these, I really like the look and I hope they hold up well. Thanks for the picts...

Does anybody have any pictures of any 5 year old wall panels in a self serve bay? I’ve got some 20 year old FRP and it looks like ass. I don’t have a lot of vandalism , but people do stupid stuff. I’ve been told that the newer stuff is better than it was as far as holes. Any picture of self...

I’m about to replace some FRP That is twenty years old In self serve bays. It has served me well and I can acid wash it and it looks like I gave my pig a bath. I’m leaning toward the wall panels from Delpro. Can anyone give me a good reason not to use the wall panels. I was also wandering how...

No, I think you have a dema 573 valve that needs replacing

Its an air operated diverter, they are usually used to divert from rinse water to spot free.

12 total. One 5 column and eleven single vendors. The 5 column is in excellent condition and the singles are mostly pretty good with a couple being beat up a little. There is one armor all can vendor. I’d like to sell them all together for $1800. Send a message if interested and I will...

The valve I replaced was the Dema 573, the one in picture 5 labeled soap.

Just had the identical issue. My soap valve was bad and forced presoak into my rinse tank causing foam. The valve body had warn thin and would not seal. Replaces the whole valve, 573p I believe. Problem fixed. It took me a while to figure that out.

Do you have the capacity extender that mounts to the top of the hopper?

I’ve used Fragramatics for 20 years. I have had good service from them and they have been reliable. I have replaced wear items but that’s about it. I have the shampoo vacs and the fragrance vacs. The fragrance is oil base and doesn’t freeze. The shampoo comes in summer and winter formula...

In addition to heating the arches you can add a blowdown to blow air through the water lines. The blowdown can be set to purge after every wash or can be set on a thermostat. I run my wash down to 25 degrees without doors. Below that I will shut it down until warmer weather. I like the cold...

Stainless steel arches are a real plus. I’ve got one in use that is a 2006. They do a great job but they use a lot of water and a lot of chemical. I’ve never had a problem with replacement parts (keeping my fingers crossed). It gets heavy usage, I have replaced 2 shafts and 3 sets of drive...

I have a 3 column D&S through the wall vendor that I removed from a wash that closed. It worked when removed. It’s a big vendor with a stainless face plate. I have no idea if the electronics are a match. If you are interested shoot me a message.

No phone number posted, email only and I always reply promptly

One of my locations has a water rate of $26 per thousand gallons water and sewer combined. I am at a $2 start for 3 minutes 12 seconds. It works for me. Also, I would get rid of the $8 option on your auto to boost your wash average.