Search results

I have a 2019 Goldline for Sale. The DAN is included. It is in great shape. Asking $7000. Please email with any questions. samishalash@hotmail.com

The motor starter on one of my bays keeps occasionally tripping. A reset will get it working for some time, but it's happening more often now. What should I be looking for as the cause? Best way to test?

I am putting in a new Razor and need to decide on the dryer setup. I have put in 3 overhead 15HP Premier dryers at another site and am not getting complaints. Issue here is that the current wiring would only support 3 - 10 HP dryers. There is a way I could probably run another electrical...

I need to line an IBA with FRP or similar and was wondering what everyone recommends? Should I go with Extrutech, or something different?

I have a twin tank Fleck system and the head on one tank counts down and then regenerates when it should, but on the other, the gallons stay put and it does not count down. I'm positive the softener company did something to cause it as the issue started right after their visit, but they claim...

Starting this year, one of my Portals gives me a Display I/O error right when it gets below 30 degrees or so. At first in the logs it shows Display I/O "error" and the screen still works fine. Eventually if it stays cold for a while, it changes to Display I/0 offline and the screen says...

One of my Razors does not seem to be communicating with the exit door at one of my sites. I can open/close the door manually, but nothing I do on the Razor screen has an effect on it. The entrance door to the same machine has no issues. What can I look for as the cause? Thanks.

I have a soap injector on my Tandem that will have suction for a few seconds once turned on, but then the suction stops. I replaced the injector and rebuilt the solenoid, but can't see anything else that I would suspect as causing the issue? Maybe it went out and got married? I can't find...

I have several of these solenoids, but no coils for them. No markings to say what brand. Anyone recognize these?

I am considering ripping out my concrete and putting in new floor heat at one location. I'm confused about what depth concrete I need to get quoted. I think the floor heat loops sit about 2" under the surface, but I'm told I need 6-8" of concrete. How would that work, and how deep would I...

I just got back in town and stopped by one wash only to hear the carbon filter running not stop. I first thought it was just mid cycle, but then found out it had been running for 4 straight days. Water was running out of the drain line at high pressure. I bypassed it for now as my spot free...

The long pipe on my radiant heater wore out in a spot and I need to put in a coupling and replace the last 1' or so where it goes into the main housing. I was thinking a coupling and 1' of 3" pipe. What material should I be looking for? Is there something specifically made for those?

I need to replace a lock in my Portal and am trying to figure out what size I need. If I for example order a 2" extension lock like in this link: https://www.kleen-ritecorp.com/p-45889-medeco-63w-750-m7-k-threaded-extension-lock-with-key-2.aspx where is the 2" measured from? Is it the whole...

I have a JC shampoo/vac that I'm having issues with. The compressor runs, but is not putting out any air. Is that something that can be fixed, or do I need to replace the compressor?

I want to put up a banner by the street to promote my new Razor. I'm having a hard time coming up with a good banner that is easy to read and conveys that there is a new touchless wash. Anyone have a banner they've used for the same purpose that could share an image with me? Thanks.

We've been having an intermittent issue with one of our G5's where the wash shuts down either during the 2nd presoak, or right afterwards during the HP rinse. The pump will start struggling an making noise and the machine shuts down and gives the error code "pump in error". It would happen...

I need to replace one of the 24v reset switches on my Ginsan Pump stand. Could someone direct me to a replacement on KR if they have one? For now I just bypassed it as it was tripping multiple times per day. Thanks.

The breaker for the spot free delivery pump on my Razor keeps tripping. First it would last a couple weeks, now it's doing it throughout the day. Pump going bad, or something I can check and adjust? There is a sensitivity dial on the breaker itself What does that do? Thanks.

I am trying to get the floor heat going at my new site, but can't get the flow switch to work properly. I've tried every size paddle with no luck. If I open the bypass, it gets enough flow and the contact makes, but I can't leave it that way since the bypass is supposed to be closed. Circ pump...

I need to replace a brine valve at another site and was wondering if anyone recognized this brine valve or RO system and could direct me to the best place to buy the valve? Thanks.